☎+86-577-86826961

sales@eaglefittings.com

Pneumatically Actuated Butterfly Valves for Sale

Pneumatically Actuated Butterfly Valves for Sale

A pneumatically actuated butterfly valve is essentially two items bundled together: there is a valve body, with the disc and seat, and the actuator that rotates the stem through 90 degrees under the direction of an operator.

It is important to select the correct pneumatic actuator for the valve. This requires matching the actuator torque output to the needs of the valve, determining what type of seat material will work best with the fluid being used, and ensuring that the plant's air supply meets the specifications for the actuator being purchased.

Quick answer: A sanitary stainless steel butterfly valve with a pneumatic actuator costs about $150 to $300 for 1", $220 to $420 for 2", $350 to $650 for 3", and $550 to $950 for 4" sizes (all with double acting actuators included). If you need to add a spring return actuator, you can expect an additional cost of approximately $30 to $80. Off-the-shelf items are typically shipped out within 3 to 7 days, while made-to-order valves can take between 2 to 4 weeks, and items that require a positioner or custom seat can take from 4 to 6 weeks. To successfully place an order for a pneumatic butterfly valve, you should know the following specification items: (1) body material, (2) seat material, (3) actuator type, (4) air supply pressure, (5) mounting standard, and (6) fail position.

When You Buy One, You Will Receive

The valve body and bore, a disc attached to a stem that rotates, and a seat to provide sealing. There is also an actuator composed of a piston moving inside of a cylinder with either a rack and pinion mechanism or a scotch yoke, which converts linear movement of the piston into 90 degrees of rotation of the valve and provides the means for controlling the open/closed position of the valve. To connect the actuator and the valve there will be a mounting interface, as well as ports on the actuator for supplying compressed air to the actuator and brackets for mounting any needed accessories, such as solenoid valves, limit switch boxes, control positioners, filter regulators, etc.

Accessories for the valve/actuator package are not typically included in the quotation, but they can impact pricing significantly. Therefore, a quotation with one price for a "pneumatic butterfly valve" and a different price for a package that includes four accessories are not considered the same type of quotation.

The mounting interface between the valve and actuator has been standardised under the ISO 5211 standard, which specifies the flange pattern and the means of connecting shaft drive to the actuator. This industry-standard enables a product from one manufacturer (an actuator) to work with a product from another manufacturer (a valve). Furthermore, the same standard allows the user to replace their actuator without having to replace the valve.

The Actuator: Double Acting or Spring Return

The actuator type can either be double-acting or spring-return.

Double-acting actuator applies pneumatic pressure on the actuator from both sides of the piston, using pneumatic pressure to open; using pneumatic pressure to close. If there is no pressure the actuator will remain in the position prior to the loss of pneumatic pressure. Double acting actuators are less costly than spring return and require a 4 way solenoid valve for operation. Double acting actuators are the appropriate choice if the loss of pneumatic pressure doesn't present a safety risk.

Spring return actuators are designed such that when pneumatic pressure is lost the spring assembly shifts the valves position to either the closed or open position, based on the configuration of the spring. Spring return actuators typically cost $30-$80 more than double acting actuators. However, spring return actuators are the preferred option if the safe condition of the process is the closed position of the valve, which is common for sanitary pipelines.

Control is another parameter to consider when selecting an actuator. Motorized actuators will open and close with pneumatic supply only. Positioners use feedback loops to manipulate the opening of the valve to the level required by the control loop (40%) based on flow, temperature, etc. Positioner prices vary depending on the construction and size of the actuators they are being paired with; therefore, it will be determined by the process engineer and not the purchaser.

Lastly, air quality should be taken into account by buyers. Rack and pinion actuators use clean, dry air at pressures between 4 and 7 bar; any plant that supplies air that is oily or wet will see seal failures in less than one year. A $40 filter regulator mounted at the valve will save the customer a $200 repair bill.

Price Differences for Valve Body and Seat

While valve body and seat are manufactured to the same general specifications for sanitary work, the materials used differ based upon the application. The sanitary valve body is typically 316L stainless steel and can be manufactured by investment casting or machining from bar stock. The sanitary valve body has either a clamp end, threaded end, or weld end. The surface finish of the wetted parts of sanitary valves is defined by an Ra value and is usually specified as an Ra value of 0.8 µm for product contact, although higher Ra values are typically specified for pharmaceutical-grade products.

The seat of a sanitary valve is application-specific. EPDM is the standard elastomeric seat material for water, steam below 150 °C, and the majority of food products, and is the least expensive. PTFE and its variants are used for higher temperature applications and aggressive chemicals, but do not provide as good of a seal at lower pressures than EPDM. FKM is a good choice for dealing with oils and hydrocarbons. Silicone is used when a product requires it, and at moderate temperatures.

The disc of a sanitary valve is typically manufactured from the same stainless steel as the body and has been polished. In the event of galling or product adhesion, a disc coated with either nylon or PTFE is available. The sizes and ends of sanitary butterfly valves are organized by size and end connection as opposed to actuator type; this is how line schedules are generated.

One item that may surprise buyers concerning price is the certificate. A valve with a compliant design to 3-A or EHEDG, a certificate of compliance to EN 10204 with a material certification 3.1 and a product's surface finish have a higher price than a valve with only a generic declaration and therefore the dairy and/or pharmaceutical application will ask for all three.

Sizes, Torque and Air Supply

Sanitary butterfly valves have clamp sizes from 1/2 inch to 12 inch, with the low end (1-4 inch) covering most process lines. The actuator is sized for torque at the valve stem, which is a function of the diameter's square and the pressure differential across the closed disc.

Two torque figures are key. Break torque is required to open a valve that has been shut against pressure, and running torque is required to keep the valve moving once it has been removed from the seat. The actuator must produce break torque at the minimum air pressure guaranteed by the facility, not the nominal air pressure, thus the margin is where under sized actuators cause issues.

At 6 bar line pressure, the break torque required for a 2 inch valve is generally 15-25 Nm, while a 4 inch valve typically requires 40-70 Nm. A double acting actuator at 5.5 bar typically generates around 10 Nm of torque per 32 mm of piston diameter in a rack and pinion design, which is why actuator sizes increase between valve sizes, rather than gradually.

The air supply is often overlooked as a limiting factor. An actuator plant with a nominal pressure rating of 5.5 bar is generally fine for all sizes and varieties of actuators, and an actuator plant with a nominal pressure rating of 4 bar may require upgrading to the next actuator size up. This is the scenario where the selection requirements for stainless steel butterfly valves will be utilized; they are defined in detail as a specification because they are based on both torque and pressure arithmetic.

Pricing

Prices shown in the table are illustrative only for 316L stainless steel sanitary valves with pneumatic actuation, i.e., double acting actuators, solenoid valve, and limit switch. All prices are shown as ex-works prices, in U.S. dollars. Additional prices for spring return, positioners, and certified 3-A or EHEDG packaging are also shown below.

Size Manual Valve Air-to-Actuate Pneumatic Valve Air-to-Actuate Pneumatic Valve with Positioner
1 inch $25 to $55 $150 to $300 $320 to $650
1.5 inch $32 to $70 $180 to $350 $360 to $720
2 inch $40 to $85 $220 to $420 $420 to $820
2.5 inch $55 to $110 $280 to $520 $500 to $950
3 inch $70 to $140 $350 to $650 $600 to $1,100
4 inch $110 to $220 $550 to $950 $850 to $1,450
6 inch $180 to $340 $900 to $1,500 $1,300 to $2,200

The manual column shows the pricing used to establish comparisons by the prospective purchasers so that they can better understand the difference in price for each of the different types of actuator. The reason that the manual price is included is that there is generally a price difference between the manual valve versus the pneumatic actuator, which causes the price inquiry and comparison to arise. For example, a manual valve at 2 inches with a price of $60 compared to a price of $320 for the pneumatic version shows a difference of $260 per valve, which will pay back for itself rather quickly in a manufacturing line that has three manual valves that require an employee to walk to their location. The pricing for a 2.5” butterfly valve can be determined by the same calculations as for any size butterfly valve, including the distinction between the clamp (ANSI) and weld (excluded) ends. The prices for these valves are equally influenced by stainless steel scrap pricing, and, therefore, any pricing quote is generally valid for thirty days only, not for a season.

Lead Times and What Can Be Shipped from Stock

In general, common sizes in EPDM with a double-acting actuator can be shipped from stock within three to seven days; whereas, made-to-order sizes, rare or uncommon end connections, and PTFE seat valves will generally take between two and four weeks to be received. Units that require a positioner, a certified package, or custom mounting will typically require between four and six weeks lead time to ship; delay for these units is generally caused by the certificate and not the valve itself.

Three items may extend lead times longer than anticipated by most buyers. Thus, both the 3-A and EHEDG certificates, along with a surface finish report, are generated after the valve is manufactured; therefore, these certificates may cause extended lead-times. The material certificate 3.1 for the body and disc will also extend the lead-time because the mill certificate must be traced to the heat number thus requiring additional time. Finally, both nonstandard actuator colour or a nameplate with the customer's name are often considered minor items, yet require additional time of approximately one week.

A practical tip is to order the valve with its accessory. If, for example, a particular valve can be shipped in one week and the solenoid can be shipped in three weeks, the valve will not be able to operate for three weeks.

Sanitary Applications: Where We Fit

Most of the demand for sanitary applications comes from four common applications.

  • Product isolation at the point of transfer, where the valve will open or close based on an external signal from the process.
  • Tank outlet isolation, to drain the valve completely and to clean it when using a CIP system.
  • Flushing the valve in a header using caustic or steam, using a SIP system.
  • Discharge control using a filler or separator, where the valve cycles thousands of times per week.

Each application has its unique design requirements. The product isolation application requires a bubble tight seat with a fast actuation, while tank outlet isolation needs a valve that does not create a pocket of liquid. This design requirement relates to the body design of the valve, not to the actuator. When using the CIP routing application, the seat must be able to withstand caustic applications at 80°C and steam at 130°C. For this reason, the material typically used for the seat is either EPDM or a PTFE variant rather than an ordinary elastomer. Filler discharge applications require a cycle life of millions for their actuators, and it is at this point where the most cost-effective actuators begin to fail.

The guide to sanitary butterfly valve types and uses lists out the applications of the different configurations of sanitary butterfly valves and this is intended to be used as a resource when specifying an actuator to be used with a CIP header.

Industrial and Utility Valves: Where to Buy Instead

Unlike sanitary butterfly valves that are used exclusively in sanitary applications, industrial and utility valve products are targeted toward other industries. Industrial butterfly valves are available in several configurations, some examples include Wafer-style or Lug-style valves for water mains; Grooved style valves for Fire mains; and High-performance style valves for Chemical lines. The industrial butterfly body pattern is typically a material combination of Cast Iron; Ductile Iron; Carbon Steel or Stainless steel that meets the standard flange bolt pattern and the actuators used for industrial butterfly valves are larger scotch-yoke actuators.

If you operate in an industrial or utility market, look for manufacturers of process valves instead of manufacturers of sanitary valves. There are several manufacturers that produce industrial butterfly valves, including Emerson, Crane, Kitz, EBRO and Alfa Laval. Each of these manufacturers has strengths and weaknesses in their respective product ranges. Emerson produces products that are designed to be integrated into automation systems, Crane manufacturers products suitable for water and process applications, Kitz produces products suited for marine and utility applications, EBRO produces products specifically designed for actuator and switchbox combinations.

A sanitary clamp valve cannot replace a flanged industrial valve, nor can an industrial flanged valve replace a sanitary clamp valve. The type of end connection determines what type of application the valve will be used in. Attempting to substitute one type of valve for the other generally results in the need for an adaptor that ultimately leaks.

Choosing By Application

The following table shows how to match the application of a valve to its configuration. The table assumes that the application is for a sanitary process line.

Application Valve Actuator Price Range
Product Isolation, 1 to 2 inch 316L clamp EPDM seat Double Acting Solenoid Limit Switch $150 to $420
Tank Outlet Drainable 316L Clamp, Cavity Free Body Spring Return Fail Closed $220 to $520
CIP/SIP Header 316L, PTFE or high temperature EPDM Double Acting w/ Position Feedback $350 to $950
Filler/Separator Discharge 316L, Ra 0.8 µm High Cycle Double Acting Fast Solenoid $420 to $1100
Manual Bypass 316L (Clamped Handle) None $25 to $220
Water Main Flanged Ductile Iron Wafer EPDM Industrial Scotch Yoke Buy from Process Valve Manufacturer
Compressed Air Line Brass or Stainless Steel, BSP End Double Acting Different Product Family

It should be noted that the row for "Compressed Air" is included for reference because this issue comes up frequently in questions. A butterfly valve can isolate a compressed air line, making it appropriate for high-flow applications with moderate pressure applications. However, as the disc is positioned in the flow path, it is a poor option for operations in which the flow rate is at a low, as the operation of the valve is going to create a noisy and unstable environment for your air line. In these low-flow cases, it would be more appropriate to use a ball valve as an isolation device.

The Order is Based on Six Specification Elements

There are six items that should go in every Purchase Order. If a supplier receives all six of these items, they can quote you based on this information without having to follow up with you via an email. The first two are the body material and the end connection. Give the name of the corresponding standard as well. The third item is seat material and the fourth is the temperature range. Together, those two will determine the actuator torque based on valve size, line pressure and actuator type, i.e., double acting or spring return and the fail position. The fifth item is the air supply pressure available to the site. Finally, the sixth item is accessories. These should be listed individually and not collectively as “complete.”

The seventh item is documentation. This item is always added after the fact. Therefore, if a project must have a 3.1 material certificate, a surface finish report, and a 3-A declaration, the order should specify this when requesting the quote. The above documents will be generated upon receipt of the order and not after.

The sanitary pipeline standards are what provide a point of reference for a dairy or pharmaceutical project inspection to take place. Therefore, if the valve meets the dimensional standard but fails to meet the finish requirement, the valve will not be accepted at commissioning, but only at delivery.

Where Eagle Fits

At Eagle, we specializein manufacturing sanitary butterfly valves, which include 316L stainless steel butterfly valves ranging in size from ½ inch to 12 inches, in clamp, weld and threaded end configurations; and using EPDM, PTFE and FKM seats. These valves are either manual or pneumatically actuated and can come with solenoids, limit switches and positioners as part of an assembled package.

What differentiates Eagle from a general valve distributor is that we provide you with both the finished product and a certificate of quality. The wetted surfaces of the valve body are machined and polished to an Ra 0.8 µm; the certificates of material trace back to a specific heat number; and the assembly is pressure tested prior to shipment. These three items represent what your food and pharmaceutical customers are actually purchasing when they buy sanitary valves, and they are why sanitary valves cost more than those of comparable size and type for industrial use.

Eagle does not manufacture industrial flanged valves that are used for water lines or fire lines. These valves are constructed from materials and standards that differ from sanitary valves. Therefore, if your project is requesting industrial flanged valves, you should consult with an industrial valve manufacturer.

FAQ

What is the operation of a pneumatic actuator on a butterfly valve?

The actuator converts compressed air into linear motion via a piston that drives a rack and pinion or a scotch yoke into a quarter turn. The disc is rotated from the open position to the closed position through a 90-degree rotation of the stem. A solenoid/divertor then moves the air flow and a limit switch or positioner tells or controls the position of the valve.

Can I use butterfly valves to stop my compressed air from leaking?

Butterfly valves can be used for isolating flows where the air is in a high-pressure area with a large flow rate. In this case, a metal or brass valve body with a proper seating surface is acceptable. They would not be the best choice for throttling low-pressure air flows as the disc will be in the flow stream creating noise and a higher level of instability in the system. The best valve to use for small air lines would be a ball valve.

How do pneumatically-operating valves operate?

A pneumatic actuator converts the air pressure to mechanical force via the actuator. Double-acting pneumatic actuators provide air pressure to both sides of the valves providing a means of "holding" the valve in place in the event of the loss of air pressure. Spring-return pneumatic actuators use a spring pack to return the valve to a safe position when the air fails to open/close the valve. Typically, pneumatic conduits are provided with an air supply pressure range of 4 to 7 bar.

What is a pneumatic-actuated valve?

One with an actuator powered by air, as opposed to being operated by either a manual handle or an electric motor. Pneumatic-actuated valves are used where fast cycling is necessary, in hazardous areas where electric-motor-actuators are not approved or for fail-safe applications, which would allow a spring-return actuator to return the valve to a safe condition in the event of air failure.

Will I need to purchase a spring-return actuator?

You should consider a pneumatic actuator with spring-return capabilities whenever the process states that the pipe must be at a specific position in the case of an air failure or to drain liquid. Typically, the safe closed position of a valve is defined by the location of the compressor in case of failure. Therefore, when using pneumatic actuators with spring return, you will have an additional cost of $30-$80 to purchase the spring-return actuator compared to a double-acting actuator.

What lead time can I expect for delivery of the equipment?

Delivery of equipment with double-acting actuators is typically available from stock in three to seven days for common sizes. You can expect two to four weeks to be delivered for equipment sizes that are custom made or for equipment with PTFE seating material. Four to six weeks should be allowed for the delivery of custom-made equipment with a positioner, a 3.1 material certification or for equipment packaged using 3-A methods.

References

Conclusion

Although the valve is the least expensive component of a valve assembly, the actuator is the device that determines whether the assembly can run or not. Size the actuator according to the break torque at the lowest level of air pressure that can be guaranteed by the plant and designate the fail position of the valve prior to placing your order. Do not wait until after the first loss of air before determining the fail position.

When creating an estimate for a pneumatic actuator, be sure to include the following two figures: the torque measured in Nm and the bar-pressure of the air supply. All remaining items -- the valve seat shape, finish, and certification -- are all defined by previously established specifications within the application.

Kontaktformular